| 2835 - 2843 |
Review: Processing of metals by equal-channel angular pressing
Furukawa M, Horita Z, Nemoto M, Langdon TG |
| 2845 - 2850 |
Elastic and viscoelastic behavior of filament wound polyethylene fiber reinforced polyolefin composites
Kazanci M, Cohn D, Marom G |
| 2851 - 2863 |
A crystal plasticity materials constitutive model for polysynthetically-twinned gamma-TiAl+alpha(2)-Ti3Al single crystals
Grujicic M, Batchu S |
| 2865 - 2874 |
Morphology development of isotactic poly(4-methylpentene-1) during melt crystallization
Silvestre C, Cimmino S, Di Pace E, Di Lorenzo ML, Orsello G, Karasz FE, Lin JS |
| 2875 - 2884 |
The theta projection method and small creep strain interpolations in a commercial Titanium alloy
Evans M |
| 2885 - 2898 |
Factors affecting the adsorption of stabilisers on to carbon black (flow micro-calorimetry and FTIR studies) - Part I -Primary phenolic antioxidants
Pena JM, Allen NS, Edge M, Liauw CM, Santamaria F, Noiset O, Valange B |
| 2899 - 2909 |
Determination of the strength of dental phosphate-bonded investments by 2 and 3 parameter Weibull analysis
Curtis RV, Juszczyk AS |
| 2911 - 2924 |
Mechanical properties and shear failure surfaces for two alumina powders in triaxial compression
Zeuch DH, Grazier JM, Arguello JG, Ewsuk KG |
| 2925 - 2930 |
Characterization of ZrO2 and SiC ceramic thin films prepared by electrostatic atomization
Miao P, Balachandran W, Xiao P |
| 2931 - 2935 |
Improvements in refractoriness and properties of Nicalon fibres by high-temperature heat-treatment
Demir A, Thompson DP |
| 2937 - 2953 |
Multi-length scale modeling of chemical vapor deposition of titanium nitride coatings
Grujicic M, Lai SG |
| 2955 - 2964 |
Influence of mechanical milling on microstructure of 49Fe-49Co-2V soft magnetic alloy
He J, Zhou F, Chang G, Lavernia EJ |
| 2965 - 2975 |
Comminuted thermoset recyclate as a reinforcing filler for thermoplastics - Part I - Characterisation of recyclate feedstocks
Bream CE, Hornsby PR |
| 2977 - 2990 |
Comminuted thermoset recyclate as a reinforcing filler for thermoplastics - Part II - Structure-property effects in polypropylene compositions
Bream CE, Hornsby PR |
| 2991 - 2997 |
Incorporation of bismuth into Ba6-xR8+2/3xTi18O54(R = Nd, Gd)
Valant M, Suvorov D |
| 2999 - 3001 |
The effect of oxygen pressure on the rate of non-isothermal thermo-oxidation of low density polyethylene
Budrugeac P |
| 3003 - 3010 |
Thermal conductivity of dense and porous yttria-stabilized zirconia
Schlichting KW, Padture NP, Klemens PG |
| 3011 - 3025 |
Fracture variability and R-curve behavior in yttria-stabilized zirconia ceramics
Casellas D, Alcala J, Llanes L, Anglada M |
| 3027 - 3033 |
Grain growth at the free surface of WC-Co materials
Olson JM, Makhlouf MM |
| 3035 - 3040 |
Effects of Ca addition on the microstructure and mechanical properties of AZ91magnesium alloy
Wang QD, Chen WD, Zeng XQ, Lu YZ, Ding WJ, Zhu YP, Xu XP, Mabuchi M |
| 3041 - 3053 |
Investigation of properties of fiber/matrix interphase formed due to the glass fiber sizings
Tanoglu M, Ziaee S, Mcknight SH, Palmese GR, Gillespie JW |
| 3055 - 3059 |
Hydrothermal synthesis of HNbWO6/MO series nanocomposites and their photocatalytic properties
Wu JH, Yin S, Lin Y, Lin JM, Huang ML, Sato T |
| 3061 - 3066 |
Preparation of porous hydroxyapatite
Tian JT, Tian JM |
