| 977 - 979 |
Mechanical properties and interfacial interaction of a novel bioabsorbable chitin fiber reinforced poly(epsilon-caprolactone) composite
Yang A, Wu RJ |
| 981 - 982 |
Investigation of the new guest-host polyetherketone poled polymer
Pan QW, Shi W, Gu QT, Wu XW, Fang CS, Yu JZ |
| 983 - 985 |
Response of Michelson interferometric fiber-optic sensors to plate waves generated by out-of-plane motion
Tsuda H, Ohiwa K, Urabe K |
| 987 - 989 |
Denucleation and substantial undercooling of DD3 superalloy in the Si-Zr-B coating mold
Liu F, Yang GC |
| 991 - 995 |
Comparison of refinement mechanism between Ni70Cu30 and Ni-based superalloy
Liu F, Yang GC |
| 997 - 999 |
Empirical correction factor for the best estimate of Weibull modulus obtained using linear least squares analysis
Davies IJ |
| 1001 - 1003 |
An in situ method to evaluate the interfacial reaction during multiple remelting
Fan TX, Zhang D, Shi ZL, Wu RJ |
| 1005 - 1007 |
Dislocation substructure in pure titanium fabricated by powder metallurgy with hot pressing at 1100 degrees C under a pressure of 20 MPa
Chu CL, Yin ZD, Zhu JC, Lin PH, Shen GJ, Wang SD |
| 1009 - 1011 |
Praseodymium bis[phthalocyaninato] complex based gas sensor using a charge-flow transistor
Xie D, Jiang YD, Jiang JZ, Wu ZM, Li YR |
| 1013 - 1015 |
A study on erbium bis[octakis(octyloxy)phthalocyaninato] sandwich complex based gas-sensitive Langmuir-Blodgett films
Xie D, Jiang YD, Jiang JZ, Li YY, Wu ZM |
| 1017 - 1019 |
Flexural mechanical properties of piassava fibers (Attalea funifera)-resin matrix composites
Aquino RCMP, D'almeida JRM, Monteiro SN |
| 1021 - 1023 |
Rietveld refinement of aluminum sheet with orientation distribution function
Kim YI, Bae YH, Jung MJ, Kim KH |
| 1025 - 1027 |
Influence of tempering temperature on damping capacity in a high carbon steel
Jun JH, Lee YK, Lee DY, Leem DS, Choi CS |
| 1029 - 1031 |
Electrorheological fluids based on chitosan particles
Jang WH, Cho YH, Kim JW, Choi HJ, Sohn JI, Jhon MS |
| 1033 - 1035 |
Contact strength measurements on a soft PZT ceramic
Fett T, Munz D, Thun G |
| 1037 - 1039 |
Fracture toughness of polyphosphate glasses in relation with chemical composition and curing process
Bigerelle M, Iost A, Gomez F, Vast P |
| 1041 - 1042 |
Quantitative mineralogical analysis of ceramic raw materials: An alternative approach
Coelho C, Scopel CA, Roqueiro N, Hotza D |
| 1043 - 1045 |
The anomalous behavior of Al-Cu-Fe quasicrystal during nanoindentation
Dub SN, Milman YV, Lotsko DV, Belous AN |
| 1047 - 1048 |
Behavior of aluminum foams under quasi-static and crash loadings
Gassan J, Harwick W, Girlich D |
| 1049 - 1050 |
Aluminum metallic substrate induce colossal biomineralization of the calcareous hydrocoral Millepora dichotoma
Vago R, Pasternak G, Itzhak D |
| 1051 - 1054 |
Electrical property-microstructural defect relationship for oxide films formed on nickel during high-temperature oxidation
Song SH, Xiao P |
| 1055 - 1057 |
Electrochemical synthesis and physical characterization of a compact hybrid film polypyrrole/PW12O403-
Cheng SA, Otero TF |
| 1059 - 1061 |
Micro-structural evolution of compositionally step-varied BST thin films by sol-gel process
Tian HY, Luo WG, Pu XH, He XY, Qiu PS, Ding AL |
| 1063 - 1065 |
Temperature dependence of morphology of TiC reinforcement in in situ Ti-6Al/TiC composites
Zhang EL, Jin YX, Zeng SY, Zhu ZJ |
| 1067 - 1070 |
Pressureless sintering of Si3N4 powders obtained from carbothermally reduced sepiolite
Kurt AO, Davies TJ |
| 1071 - 1075 |
Sol-gel synthesis of monazite-type cerous phosphate for fiber coating
Li B, Shen LY, Liu XZ, Zhang SH, Zhang YM, Wang TM, Sasaki Y, Ishii K, Kashiwaya Y, Takahashi H, Shibayama T |
