J33 - J42 |
Ionic transport in Gd3Fe5O12- and Y3Fe5O12-based garnets Kharton VV, Shaula AL, Naumovich EN, Vyshatko NP, Marozau IP, Viskup AP, Marques FMB |
A851 - A857 |
Electrochemical reduction of oxygen on gold nanoparticle-electrodeposited glassy carbon electrodes El-Deab MS, Okajima T, Ohsaka T |
A858 - A863 |
A study of direct-conversion SOFC with n-butane at higher fuel utilization Costa-Nunes O, Vohs JM, Gorte RJ |
A864 - A867 |
Carbon nanotube/RuO2 nanocomposite electrodes for supercapacitors Park JH, Ko JM, Park OO |
A868 - A872 |
A fuel cell development for using borohydrides as the fuel Li ZP, Liu BH, Arai K, Suda S |
A873 - A877 |
Development of ceramic gas separator for SOFCs Murata K, Nishimura N, Doi N |
A878 - A884 |
Equilibria in fuel cell gases - I. Equilibrium compositions and reforming conditions Sasaki K, Teraoka Y |
A885 - A888 |
Equilibria in fuel cell gases - II. The C-H-O ternary diagrams Sasaki K, Teraoka Y |
A889 - A893 |
Effect of multiwalled carbon nanotubes on electrochemical properties of lithium sulfur rechargeable batteries Han SC, Song MS, Lee H, Kim HS, Ahn HJ, Lee JY |
A894 - A898 |
Single bath, pulsed electrodeposition of copper-tin alloy negative electrodes for lithium-ion batteries Beattie SD, Dahn JR |
A899 - A904 |
Band-edge Potentials of n-type and p-type GaN Beach JD, Collins RT, Turner JA |
A905 - A911 |
Study of mn dissolution from LiMn2O4 spinel electrodes using rotating ring-disk collection experiments Wang LF, Ou CC, Striebel KA, Chen JJS |
A912 - A916 |
An electrochemical and XRD study of lithium insertion into mechanically alloyed magnesium stannide Roberts GA, Cairns EJ, Reimer JA |
A917 - A921 |
The microstructure and character of the PVDF-g-PSSA membrane prepared by solution grafting Qiu XP, Li WQ, Zhang SC, Liang HY, Zhu WT |
A922 - A927 |
Development and characterization of a thick-film printed zinc-alkaline battery Ghiurcan GA, Liu CC, Webber A, Feddrix FH |
A928 - A932 |
Thermoelectric power of M-H systems in molten salts and application to M-H thermogalvanic cell Murakami T, Nishikiori T, Nohira T, Ito Y |
A933 - A941 |
Lithium hectorite clay as the ionic conductor in LiCoO2 cathodes Riley MW, Fedkiw PS, Khan SA |
A942 - A951 |
Fuel composition and diluent effect on gas transport and performance of anode-supported SOFCs Jiang Y, Virkar AV |
A952 - A958 |
Expansion behavior of Ce1-yGdyO2.0-0.5y-delta under various oxygen partial pressures evaluated by HTXRD Wang SR, Katsuki M, Hashimoto T, Dokiya M |
A959 - A965 |
Electrochemical behavior of the polyaniline-organosulfur composite film containing Ag nanoparticles Park JE, Park SG, Koukitu A, Hatozaki O, Oyama N |
A966 - A969 |
Mixed-metals codeposition as a novel method for the preparation of LiMn2O4 electrodes with reduced capacity fades Eftekhari A |
A970 - A972 |
The effect of ZnO coating on electrochemical cycling behavior of spinel LiMn2O4 cathode materials at elevated temperature Sun YK, Hong KJ, Prakash J |
A973 - A978 |
Methanol oxidation on Pt/Ru, Pt/Ni, and Pt/Ru/Ni anode electrocatalysts at different temperatures for DMFCs Choi JH, Park KW, Kwon BK, Sung YE |
A979 - A984 |
A nanostructured honeycomb carbon anode Li NC, Mitchell DT, Lee KP, Martin CR |
A985 - A989 |
Li+ storage sites in amorphous V2O5 prepared by precipitation method Kim TA, Kim JH, Kim MG, Oh SM |
A990 - A993 |
Synthesis and electrochemical properties of high capacity V2O5-delta cathodes Kannan AM, Manthiram A |
A994 - A999 |
Synthesis and electrochemical properties of some lithium chelatophosphates Eberwein M, Schmid A, Schmidt M, Zabel M, Burgemeister T, Barthel J, Kunz W, Gores HJ |
B295 - B302 |
Corrosion and electrochemical properties of Sn-8% Zn alloy-coated steel in methanol containing H2O, NaCl, and HCOOH Umebayashi R, Akao N, Hara N, Sugimoto K |
B303 - B308 |
Understanding the degradation of organic coatings using local electrochemical impedance methods - I. Commonly observed features Mierisch AM, Taylor SR |
B309 - B315 |
Understanding the degradation of organic coatings through local electrochemical impedance methods - II. Modeling and experimental results of normal field variations above disk electrodes Mierisch AM, Taylor SR, Celli V |
B316 - B324 |
In situ STM study of the initial stages of anodic oxidation of Cu-(111) in the presence of sulfates Maurice V, Klein LH, Strehblow HH, Marcus P |
B325 - B328 |
Oxidation kinetics of a lead electrode covered with an anodic Pb-(II) film in sulfuric acid solution Ma M, Yang CX, Cai WB, Zhou WF, Liu HT |
B329 - B335 |
Assessment of proton transport in amorphous aluminum oxide by cathodic polarization - Time of flight-elastic recoil detection analysis method Seo JH, Lee DN |
B336 - B341 |
Temperature dependence of surface crystal structures of iron passivated at-400 mV in a borate buffer solution Deng HH, Qian P, Sanada N, Yoneya M, Nanjo H |
B342 - B347 |
Lewis acid/Lewis base effects in corrosion and polymer adhesion at aluminum surfaces McCafferty E |
B348 - B354 |
Direct evidence of the electronic conduction of the passive film on iron by EC-STM Diez-Perez I, Gorostiza P, Sanz F |
B355 - B360 |
Dealloying of Ag-Au alloys in halide-containing electrolytes - Affect on critical potential and pore size Dursun A, Pugh DV, Corcoran SG |
C451 - C456 |
Via-filling capability of copper film by CVD Lin CL, Chen PS, Lin YC, Tsui BY, Chen MC |
C457 - C460 |
Single-bath electrodeposition of a combinatorial library of binary Cu1-xSnx alloys Beattie SD, Dahn JR |
C461 - C464 |
Direct plating of electroless Ni-P layers on sputter-deposited Al-Ni alloy films Azumi K, Yugiri T, Kurihara T, Seo M, Habazaki H, Fujimoto S |
C465 - C471 |
Ultrathin zirconium silicate films deposited on Si(100) using Zr(O-i-Pr)(2)(thd)(2), Si(O-t-Bu)(2)(thd)(2), and nitric oxide Chen HW, Huang TY, Landheer D, Wu X, Moisa S, Sproule GI, Kim JK, Lennard WN, Chao TS |
C472 - C477 |
In situ CRM study of the self-oscillating Cu-(II)-lactate and Cu-(II)-tartrate systems Leopold S, Arrayet JC, Bruneel JL, Herranen M, Carlsson JO, Argoul F, Servant L |
C478 - C484 |
Study of the electrochemical deposition of CaCO3 by in situ Raman spectroscopy - I. Influence of the substrate Gabrielli C, Jaouhari R, Joiret S, Maurin G, Rousseau P |
C485 - C493 |
Study of electrochemical deposition of CaCO3 by in situ Raman spectroscopy - II. Influence of the solution composition Tlili MM, Ben Amor M, Gabrielli C, Joiret S, Maurin G, Rousseau P |
C494 - C501 |
Nucleation-growth process of scale electrodeposition - Influence of the supersaturation Devos O, Gabrielli C, Tlili M, Tribollet B |
C502 - C506 |
Characterization of amorphous Ni-P coatings by small angle X-ray scattering Tatchev D, Kranold R, Armyanov S |
D129 - D133 |
Electrochemical studies of the alkene-NOx fuel cell for organic synthesis Yamanaka I, Nabae Y, Otsuka K |
E337 - E341 |
Electrochemical behavior of cobalt oxide films deposited at conductive diamond electrodes Spataru N, Terashima C, Tokuhiro K, Sutanto I, Tryk DA, Park SM, Fujishima A |
E342 - E347 |
Electrochemical characterization of carbon films with porous microstructures Kiema GK, Brett MJ |
E348 - E354 |
Theoretical analysis of IS of polycrystalline materials with blocking or conducting grain boundaries: From microcrystals to nanocrystals Bouchet R, Knauth P, Laugier JM |
E355 - E359 |
Thermodynamic evaluation of Ti-H system at medium-range temperatures by molten salt electrochemical technique Kasajima T, Nishikiori T, Nohira T, Ito Y |
E360 - E365 |
Electrochemistry of conductive polymers - XXVIII. Electrochemical preparation and characterization of poly(1,5-diaminonaphthalene) as a functional polymer Hong SY, Park SM |
E366 - E370 |
Depth profiling of the lateral pore size and correlation distance in thin porous silicon layers by grazing incidence small angle X-ray scattering Ferrero C, Servidori M, Thiaudiere D, Milita S, Lequien S, Sama S, Setzu S, Metzger TH |
F129 - F133 |
Silicon nitride films deposited using ECR-PECVD technique for coating InGaAlAs high power laser facets Sah RE, Rinner F, Baumann H, Kiefer R, Mikulla M, Weimann G, Dammann M |
F134 - F140 |
Characterization of La2O3 and Yb2O3 thin films for high-k gate insulator application Ohmi S, Kobayashi C, Kashiwagi I, Ohshima C, Ishiwara H, Iwai H |
G359 - G364 |
Effect of liner oxide densification on stress-induced leakage current characteristics in shallow trench isolation processing Park JH, Shin SW, Park SW, Kong YT, Kim DJ, Suh MS, Lee SC, Kwak NY, Dong CD, Kim DW, Lee GI, Kwon OJ, Yang HS |
G365 - G370 |
Diffusion properties of ion-implanted vanadium in PECVD-SiO2 and PECVD-SiNx Isenberg J, Reber S, Warta W |
G371 - G375 |
Method for thin-film technology of Si with doping Nishizawa J, Kurabayashi T, Oizumi T, Kikuchi H, Yoshida T |
G376 - G379 |
Surface planarization of strain-relaxed SiGe buffer layers by CMP and post cleaning Sawano K, Kawaguchi K, Koh S, Hirose Y, Hattori T, Nakagawa K, Shiraki Y |
G380 - G384 |
Carrier profiling and crystal quality evaluation of thin AlxGa1-xAs (0.22 < x < 0.86) films by electrochemical capacitance/voltage technique Fedorenko Y, Jouhti T, Konttinen J, Likonen J, Pessa M |
G385 - G388 |
Effect of a Mo interlayer on the electrical and structural properties of nickel silicides Ok YW, Choi CJ, Seong TY |
G389 - G394 |
Using anodization to oxidize ultrathin aluminum film for high-k gate dielectric application Lin YP, Hwu JG |
G395 - G399 |
Anisotropic etching of GaAs using CCl2F2/CCl4 gases to fabricate 200 mu m deep via holes for grounding MMICs Rawal DS, Agarwal VR, Sharma HS, Sehgal BK, Gulati R, Vyas HP |
G400 - G403 |
Sulfurization of Cu/In precursors for CuInS2-based solar cells Alvarez-Garcia J, Barcones B, Romano-Rodriguez A, Calvo-Barrio L, Perez-Rodriguez A, Morante JR, Scheer R, Klenk R |
G404 - G411 |
Process optimization and integration of trimethylsilane-deposited alpha-SiC : H and alpha-SiCO : H dielectric thin films for damascene processing Gray WD, Loboda MJ, Bremmer JN, Struyf H, Lepage M, Van Hove M, Donaton RA, Sleeckx E, Stucchi M, Lanckmans F, Gao T, Boullart W, Coenegrachts B, Maenhoudt M, Vanhaelemeersch S, Meynen H, Maex K |
G412 - G417 |
Plastic-compatible low resistance printable gold nanoparticle conductors for flexible electronics Huang D, Liao F, Molesa S, Redinger D, Subramanian V |
G418 - G427 |
Effects of chamber wall conditions on Cl concentration and Si etch rate uniformity in plasma etching reactors Kim TW, Aydil ES |
H147 - H155 |
Reduction of mercury loss in fluorescent lamps coated with thin metal-oxide films Hildenbrand VD, Denissen CJM, van der Pol AJHP, Hendriks AHC, van der Marel C, Snijders JHM, Tamminga Y, Brongersma HH, Viitanen MM |
H156 - H160 |
Platinum electrodes modified by tin for electrochemical CO sensors Tsceng KI, Yang MC |
H161 - H164 |
Energy transfer between Bi3+ and Pr3+ in doped CaTiO3 Jia WY, Perez-Andujar A, Rivera I |
A1000 - A1007 |
Li insertion into Li4Ti5O12 p(Spinel) - Charge capability vs. particle size in thin-film electrodes Kavan L, Prochazka J, Spitler TM, Kalbac M, Zukalova MT, Drezen T, Gratzel M |
A1008 - A1015 |
Transport in polymer-electrolyte membranes - I. Physical model Weber AZ, Newman J |