| 2165 - 2173 |
Influences of hot stretch ratio on essential work of fracture of in-situ microfibrillar poly(ethylene terephthalate)/polyethylene blends
Li ZM, Xie BH, Huang R, Fang MP, Yang M |
| 2174 - 2184 |
Morphology and mechanical properties of injection molded poly(ethylene terephthalate)
Viana JC, Alves NM, Mano JF |
| 2185 - 2193 |
Temporary networks in polymer-modified asphalts
Polacco G, Stastna J, Vlachovicova Z, Biondi D, Zanzotto L |
| 2194 - 2202 |
Polymer crystallization kinetics, master quotients, master curves and Nakamura-Ozawa-equations of iPP and PTFE
Lambrigger M |
| 2203 - 2215 |
Investigation of solids transport in a single-screw extruder using a 3-D discrete particle simulation
Moysey PA, Thompson AR |
| 2216 - 2228 |
Design of calibrators for extruded profiles. Part I: Modeling the thermal interchanges
Nobrega JM, Carneiro OS, Covas JA, Pinho FT, Oliveira PJ |
| 2229 - 2239 |
New experimental method for determination of effective diffusion coefficient of blowing agents in polyurethane foams
Modesti M, Lorenzetti A, Dall'Acqua C |
| 2240 - 2246 |
Cyclic deformation behavior of an epoxy polymer. Part I: Experimental investigation
Shen XH, Xia ZH, Ellyin F |
| 2247 - 2253 |
Fate of erucamide in polyolefin films at elevated temperature
Shuler CA, Janorkar AV, Hirt DE |
| 2254 - 2265 |
A time-scale approach for analysis of coalescence in processing flows
Perilla JE, Jana SC |
| 2266 - 2273 |
Extrusion of broad-molecular-weight-distribution polyethylenes
Krishnaswamy RK, Rohlfing DC, Sukhadia AM, Slusarz KR |
| 2274 - 2287 |
Mathematical modeling and numerical simulation of cell growth in injection molding of microcellular plastics
Osorio A, Turng LS |
| 2288 - 2297 |
Isothermal and nonisothermal crystallization kinetics of syndiotactic polystyrene/clay nanocomposites
Wu TM, Hsu SF, Chien CF, Wu JY |
| 2298 - 2307 |
Experimental studies on radial extrudate swell and velocity profiles of flowing PS melt in an electro-magnetized die of an extrusion rheometer
Intawong NT, Sombatsompop N |
| 2308 - 2317 |
Temperature control of injection molding. Part 1: Modeling and identification
Diduch C, Dubay R, Li WG |
| 2318 - 2326 |
Temperature control in injection molding. Part II: Controller design, simulation, and implementation
Dubay R, Diduch C, Li WG |
| 2327 - 2334 |
The effect of molding conditions on mechanical and morphological properties at the interface of film insert injection molded polypropylene-film/polypropylene matrix
Leong YW, Yamaguchi S, Mizoguchi M, Hamada H, Ishiaku US, Tsuji T |
| 2335 - 2339 |
Preparation and characterization of poly(methyl methacrylate)-intercalated graphite oxide/poly(methyl methacrylate) nanocomposite
Wang WP, Pan CY |
| 2340 - 2345 |
Studies on impact-modified nylon 6/ABS blends
Chiu HT, Hsiao YK |
| 2346 - 2352 |
Study of the miscibility and mechanical properties of NBR/HNBR blends
Hussein IA, Chaudhry RA, Sharkh BFA |
