Polymer Engineering and Science

Polymer Engineering and Science, Vol.47, No.12 Entire volume, number list

ISSN: 0032-3888 (Print)

In this Issue (23 articles)

1975 - 1982	Triboelectrostatic separation of covering plastics in chopped waste electric wire Park CH, Jeon HS, Cho BG, Park JK
1983 - 1991	Molecular, rheological, and crystalline properties of low-density polyethylene in blown film extrusion Majumder KK, Hobbs G, Battacharya SN
1992 - 2004	Stretching induced phase transformations in melt extruded poly(vinylidene fluoride) cast films: Effect of cast roll temperature and speed Mhalgi MV, Khakhar DV, Misra A
2005 - 2011	Miscibility and crystallization kinetics of poly(trimethylene terephthalate)/amorphous poly(ethylene terephthalate) blends Chiu HJ
2012 - 2019	Effects of surface roughness on microinjection molding Zhang HL, Ong NS, Lam YC
2020 - 2026	Ultraporous 3D polymer meshes by low-temperature electrospinning: Use of ice crystals as a removable void template Simonet M, Schneider OD, Neuenschwander P, Stark WJ
2027 - 2033	Study on epoxy/thermoplastic blends based on the addition of a novel aromatic block copolymer Cicala G, Mamo A, Recca G, Restuccia CL
2034 - 2040	The effect of polyvinylidene fluoride on nonisothermal crystallization behavior of polyoxymethylene Ding Q, Dai WL, Zhang P
2041 - 2048	The effect of epoxy-polyester hybrid resin on mechanical properties, rheological behavior, and water absorption of polypropylene wood flour composites Jahani Y
2049 - 2056	Effect of fill factor and validation of characterizing the degree of mixing in polymer nanocomposites Kim D, Lee JS, Barry CM, Mead JL
2057 - 2064	Transport characteristics of carboxylic acids based chain extended PU membranes with n-alkane penetrants Siddaramaiah, Manjula KS
2065 - 2074	Exploitation of electric field in controlling of nanofiber spinning process Heikkila P, Soderlund L, Uusimaki J, Kettunen L, Harlin A
2075 - 2084	Through-thickness embossing process for fabrication of three-dimensional thermoplastic parts Nagarajan P, Yao D, Ellis TS, Azadegan R
2085 - 2094	Modeling of dynamic mechanical properties of vulcanized fluoroelastomer Likozar B, Sebenik U, Krajnc M
2095 - 2099	Preparation and characterization of bis-ortho-diynylarene (BODA)-derived submicrogratings Zengin H, Zengin G, Zhou W, Topping CM, Smith DW, Foulger SH
2100 - 2109	Influence of screw profile and extrusion conditions on the microstructure of polypropylene/organoclay nanocomposites Lertwimolnun W, Vergnes B
2110 - 2117	Stress-strain behavior as related to surface topography and thickness uniformity in uni- and biaxially stretched PVDF/PMMA blends Zhou X, Cakmak M
2118 - 2123	Nitroxide-mediated controlled degradation of polypropylene Psarreas A, Tzoganakis C, McManus N, Penlidis A
2124 - 2128	Shrinkage behavior and mechanical performances of injection molded polypropylene/talc composites Shelesh-Nezhad K, Taghizadeh A
2129 - 2144	Nonisothermal finite-element analysis of thermoforming of polyethylene terephthalate sheet: Incomplete effect of the forming stage Erchiqui F, Souli M, Ben Yedder R
2145 - 2154	Phase structure and morphology of wollastonite-reinforced polypropylene composites modified with SEBS and SEBS-g-MA elastomers Svab I, Musil V, Jurkin T, Smit I
2155 - 2163	Chain extension and degradation during reactive processing of PET in the presence of triphenyl phosphite Cavalcanti FN, Teofilo ET, Rabello MS, Silva SML
2164 - 2171	Effects of interfacial morphology on the welding strength of injection-molded polyamide Qiu JH, Tsuboi A, Izumi K, Wu H, Guo SY, Huang YD