Polymer Engineering and Science

Polymer Engineering and Science, Vol.48, No.2 Entire volume, number list

ISSN: 0032-3888 (Print)

In this Issue (26 articles)

211 - 215	Coefficient of thermal expansion for Twaron((R)) fibers using crystallographic data Jain A
216 - 222	Processability studies of silica-thermoset polymer matrix nanocomposites Lekakou C, Kontodimopoulos I, Murugesh AK, Chen YL, Jesson DA, Watts JF, Smith PA
223 - 232	Elongational viscosity of LDPEs and polystyrenes using entrance loss data Walczak K, Gupta M, Koppi KA, Dooley J, Spalding MA
233 - 239	Structural characterization and mass transfer properties of dense segmented polyurethane membrane: Influence of hard segment and soft segment crystal melting temperature Mondal S, Hu JL
240 - 248	Morphology of PA-6 vibration welded joints and its effects on weld strength Chung YM, Kamal MR
249 - 256	Interaction of thermoplastic polyurethane with polyamide 1212 and its influence on the thermal and mechanical properties of TPU/PA1212 blends Li WL, Liu JL, Hao CW, Jiang K, Xu DF, Wang DJ
257 - 266	Optical monitoring of polypropylene crystallization during injection molding Favaro MM, Marinelli AL, Farah M, Bretas RES
267 - 276	Macroscopic failure of multilayered viscoelastic polymers Wu CH, Mantell SC, Davidson JH
277 - 282	A study of nano-mechanical and macro-mechanical properties of ethylene vinyl acetate Kim J, Wang J, Kang HJ, Talke F
283 - 291	Thermal residual stress develoment for semi-crystalline polymers in rotational molding Xu H, Bellehumeur CT
292 - 296	Tribological properties of blends of melamine-formaldehyde resin with low density polyethylene Brostow W, Datashvili T, Huang B
297 - 306	Thermoplastic polyurethane elastomers based on polycarbonate diols with different soft segment molecular weight and chemical structure: Mechanical and thermal properties Eceiza A, Martin MD, de la Caba K, Kortaberria G, Gabilondo N, Corcuera MA, Mondragon I
307 - 315	A macroscopic mathematical model for tensioned-web slot coating Lin FH, Liu CM, Liu TJ, Wu PY
316 - 328	Numerical study of nonisothermal polymer extrusion flow with a differential viscoelastic model Mu Y, Zhao GQ
329 - 335	Reverisble thermal gelation of soft semi-crystalline polyethylene microparticles with surface interactions in squalane Ling GH, Shaw MT
336 - 344	Conventional and nanometric nucleating agents in poly(epsilon-caprolactone) foaming: Crystals vs. bubbles nucleation Marrazzo C, Di Maio E, Iannace S
345 - 354	Synthesis and studies of the physical properties of polyaniline and polyurethane-modified epoxy composites Chiou WC, Han JL, Lee SN
355 - 359	Electromagnetic interference shielding with polyaniline nanofibers composite coatings Niu YH
360 - 364	Prediction of environmental stress cracking resistance in linear low density polyethylenes Maxwell AS, Pilkington G
365 - 372	Cracking formation on the surface of extruded photodegraded polypropylene plates Fechine GJM, Demarquette NR
373 - 380	Mechanical, thermal, and morphological behavior of the polyamide 6/acrylonitrile-butadiene-styrene blends irradiated with gamma rays Hassan MM
381 - 385	Weathering of recycled photo-degraded polyethylene Maxwell AS
386 - 394	Influence of molecular weight on the electrification of linear polyethylene during extrusion: Identification of two different mechanisms for charge generation Rodriguez-Gonzalez F, Perez-Gonzalez J, de Vargas L, Moreno E, Gonzalez-Santos G
395 - 404	Fiber orientation in injection molding with rotating flow Silva CA, Viana JC, van Hattum FWJ, Cunha AM
405 - 414	Sharkskin and oscillating and capillary dies and not welt fracture: Why in slit in annular dies? Delgadillo-Velazquez O, Georgiou G, Sentmanat M, Hatzikiriakos SG
415 - 423	Viscoelastic evaluation of effects of fiber size and composition on cellulose-polypropylene composite of high filler content Ito H, Kumari R, Takatani M, Okamoto T, Hattori H, Fujiyoshi I