| 373 - 379 |
The mechanical properties of insert-molded bimaterial composites
Extrand CW, Bhatt S |
| 380 - 400 |
Open-celled microcellular thermoplastic foam
Rodeheaver BA, Colton JS |
| 401 - 407 |
A new method to quantify crazing in various environments
Clay SB, Kander RG |
| 408 - 416 |
The effect of talc on the crystal orientation in polypropylene/ethylene-propylene rubber/talc polymer blends in injection molding
Obata Y, Sumitomo T, Ijitsu T, Matsuda M, Nomura T |
| 417 - 425 |
Physical chemistry of a phosphite processing stabilizer in polypropylene. Part 1: Solubility
Billingham NC, Garcia-Trabajo P |
| 426 - 439 |
Finite element analysis of blow molding and thermoforming using a dynamic explicit procedure
Marckmann G, Verron E, Peseux B |
| 440 - 448 |
Quantitative measurement of adhesion between polypropylene blends and paints by tensile mechanical testing
Tang HX, Foran B, Martin DC |
| 449 - 465 |
A 3-D finite element model for gas-assisted injection molding: Simulations and experiments
Haagh GAAV, Peters GWM, Van de Vosse FN, Meijer HEH |
| 466 - 474 |
Crystallization of poly(ethylene terephthalate) and poly(butylene terephthalate) modified by diamides
Bouma K, Gaymans RJ |
| 475 - 483 |
A new hypothesis to describe the mechanisms acting in a welded joint of semicrystalline thermoplastics
Bonten C, Schmachtenberg E |
| 484 - 491 |
Transport modeling and thermophysical properties of cellular poly(urethane-isocyanurate)
Peng S, Fuchs A |
| 492 - 503 |
Stress-initiated void formation during cure of a three-dimensionally constrained thermoset resin
Eom Y, Boogh L, Michaud V, Sunderland P, Manson JA |
| 504 - 513 |
Enthalpy relaxation in polymeric glasses
Drozdov AD |
| 514 - 521 |
Studies on epoxy modified with recycled rubber
Sipahi-Saglam E, Kaynak C, Akovali G, Yetmez M, Akkas N |
| 522 - 531 |
Elastomer biaxial characterization using bubble inflation technique. I: Experimental investigations
Reuge N, Schmidt FM, Le Maoult Y, Rachik M, Abbe F |
| 532 - 541 |
Elastomer biaxial characterization using bubble inflation technique. II: Numerical investigation of some constitutive models
Rachik M, Schmidt F, Reuge N, Le Maoult Y, Abbe F |
| 542 - 553 |
Effect of poly(acrylic acid)-g-PCL microstructure on the mechanical properties of starch/PCL blend compatibilized with poly(acrylic acid)-g-PCL
Kim CH, Cho KY, Park JK |
| 554 - 565 |
Weldline morphology of injection molded modified poly(phenylene-oxide)/polyamide-6 blends
Son Y, Ahn KH, Char K |
| 566 - 574 |
Biaxial stress relaxation of high impact polystyrene (HIPS) above the glass transition temperature
Hummel SR, Hossain K, Hayes GT |
| 575 - 583 |
Izod impact strength of a product molded of poly(vinyl chloride)/impact modifier containing voids (void MOD)
Takaki A, Narisawa I, Kuriyama T |
| 584 - 594 |
Properties and manufacturing of a new starch plastic
De Graaf RA, Janssen LPBM |
| 595 - 602 |
Rheokinetics and the influence of shear rate on the Trommsdorff (gel) effect during free radical polymerization
Cioffi M, Hoffmann AC, Janssen LPBM |
