| 1405 - 1413 |
Structure and mechanical properties of polyamide-6,6/poly(ethylene terephthalate) blends
Retolaza A, Eguiazabal JI, Nazabal J |
| 1414 - 1418 |
Numerical investigation of the influence of material properties and adhesive layer thickness on the heating efficiency of microwave curing of an adhesive-bonded joint
So HW, Taube A |
| 1419 - 1428 |
Thermal properties of biaxially deformed in situ composites
Seo YP, Seo Y |
| 1429 - 1438 |
Rheological, mechanical and biodegradation studies on blends of thermoplastic starch and polycaprolactone
Shin BY, Lee SI, Shin YS, Balakrishnan S, Narayan R |
| 1439 - 1447 |
Indentation of poly(formaldehyde), reinforced nylons and poly(ethyl terephthalate)
Benabdallah HS, Bui VT |
| 1448 - 1459 |
Mechanical and erosion properties of CaCO3-EMAA thermal sprayed coatings
Yan FY, Gross KA, Simon GP, Berndt CC |
| 1460 - 1472 |
Modeling and simulation of stretch blow molding of polyethylene terephthalate
Pham XT, Thibault F, Lim LT |
| 1473 - 1483 |
Development and characterization of reactively extruded PVC/polystyrene blends
Haba Y, Narkis A |
| 1484 - 1490 |
Online measurements of crystallinity using Raman spectroscopy during blown film extrusion of a linear low-density polyethylene
Cherukupalli SS, Ogale AA |
| 1491 - 1497 |
Kinetic and thermodynamic considerations in the synthesis of a new three-arm poly(epsilon-caprolactone)
Balakrishnan S, Krishnan M, Dubois P, Narayan R |
| 1498 - 1508 |
An axisymmetric model for thread forming in polycarbonate and polypropylene screw and boss fasteners
Ellwood KRJ, Fesko D, Bauer DR |
| 1509 - 1513 |
Effect of ultrasound on extrusion of PP/EPDM blends: Structure and mechanical properties
Chen YZ, Li HL |
| 1514 - 1521 |
Determination of the phase transition behavior of thermoplastic polyurethanes from coupled rheology/DSC measurements
Nichetti D, Grizzuti N |
| 1522 - 1533 |
The thermomechanical environment and the mechanical properties of injection moldings
Viana JC, Billon N, Cunha AM |
| 1534 - 1542 |
Investigation of morphology formation in SBS block copolymer/homopolystyrene blends
Huy TA, Adhikari R, Lupke T, Michler GH, Knoll K |
| 1543 - 1550 |
The effect of surface energy of boron nitride on polymer processability
Rathod N, Hatzikiriakos SG |
| 1551 - 1560 |
Relationship between cell morphology and impact strength of microcellular foamed high-density polythylene/polypropylene blends
Rachtanapun P, Selke SEM, Matuana LM |
| 1561 - 1570 |
Deformation and morphology development of poly(ethylene terephthalate)/polyethylene and polycarbonate/polyethylene blends with high interfacial contact during elongation
Li ZM, Fu MR, Yang SY, Yang MB, Yang W, Huang R |
| 1571 - 1578 |
Capacitive transducer for in-mold monitoring of injection molding
Chen X, Chen GH, Gao FR |
| 1579 - 1587 |
Recycled poly(ethylene terephthalate) chain extension by a reactive extrusion process
Awaja F, Daver F, Kosior E |
| 1588 - 1593 |
Injection molded automotive TPO - A multilayer composite structure of varied orientations
Strebel JJ, Mirabella F, Blythe C, Pham T |
| 1594 - 1603 |
Analysis of the creep behavior of polypropylene-woodflour composites
Nunez AJ, Marcovich NE, Aranguren MI |
