Solar Energy

Solar Energy, Vol.207 Entire volume, number list

ISSN: 0038-092X (Print)

In this Issue (119 articles)

1 - 9	Parametric strategy on passive design affordances in cool-humid climate zones of North-East India Tungnung K
10 - 21	Experimental investigation of the effect of using water and ethanol as working fluid on the performance of pyramid-shaped solar still integrated with heat pipe solar collector Fallahzadeh R, Aref L, Gholamiarjenaki N, Nonejad Z, Saghi M
22 - 31	Analysis on an optimal transmittance of Fresnel lens as solar concentrator Ma XL, Jin RH, Liang S, Liu SL, Zheng HF
32 - 39	Facile fabrication of well-performing CdS/CdSe quantum dot sensitized solar cells through a fast and effective formation of the CdSe nanocrystalline layer Marandi M, Torabi N, Farahani FA
40 - 50	Mathematical modeling and experimental validation of the thermal performance of a novel design solar cooker Khallaf AM, Tawfik MA, El-Sebaii AA, Sagade AA
51 - 58	A facile strategy of constructing composite form-stable phase change materials with superior high thermal conductivity using silicagel industrial wastes Zhang YW, Sun KY, Kou Y, Wang SX, Shi Q
59 - 76	Ruthenium complexes based dye sensitized solar cells: Fundamentals and research trends Tomar N, Agrawal A, Dhaka VS, Surolia PK
77 - 90	Measurement of flow properties coupled to experimental and numerical analyses of dense, granular flows for solar thermal energy storage Bagepalli MV, Yarrington JD, Schrader AJ, Zhang ZMM, Ranjan D, Loutzenhiser PG
91 - 102	Experimental study of pin finned receiver tubes for a parabolic trough solar air collector Zhao ZW, Bai FW, Zhang XL, Wang ZF
103 - 109	Feasibility of water-cooled photovoltaic panels under the efficiency and durability aspects Piotrowski LJ, Simoes MG, Farret FA
110 - 132	Review of heliostat calibration and tracking control methods Sattler JC, Roger M, Schwarzbozl P, Buck R, Macke A, Raeder C, Gottsche J
133 - 143	Construction strategy and performance analysis of large-scale spherical solar concentrator for the space solar power station Yang Y, Zhang YQ, Fan GH, Li M, Pei MC
144 - 156	Supercritical carbon dioxide cycles with multi-heating in Concentrating Solar Power plants Gonzalez-Portillo LF, Munoz-Anton J, Martinez-Val JM
157 - 164	Highly stable thin film organic solar cells using poly crystallized silver doped LaPO4 Hamed MSG, Mola GT
165 - 172	Theoretical pressure-tuning bandgaps of double perovskites A(2)(BB ') X-6 for photo-voltaics Yang ER, Luo X
173 - 182	Influence of flow direction and turbulence intensity on heat transfer of utility-scale photovoltaic solar farms Glick A, Smith SE, Ali N, Bossuyt J, Recktenwald G, Calaf M, Cal RB
183 - 191	Emissivity and absorption function measurements of Al2O3 and SiC particles at elevated temperature for the utilization in concentrated solar receivers Zhao WX, Sun ZW, Alwahabi ZT
192 - 198	W/AlSiTiNx/SiAlTiOyNx/SiAlOx multilayered solar thermal selective absorber coating AL-Rjoub A, Rebouta L, Cunha NF, Fernandes F, Barradas NP, Alves E
199 - 208	Core unit engineering of star-shaped acceptor polymers for all-polymer solar cells Ma MD, Ji Q, Yin LQ, Lin K, Wen GZ, Xu YX, Zhang N, Dong G, Yu LM, Zhang W, Xu XF
209 - 217	Life cycle assessment of solar communities Guarino F, Longo S, Vermette CH, Cellura M, La Rocca V
218 - 227	Simple interference based colorization of Si based solar cells and panels with ITO/SiNx:H double layer antireflective coatings Rudzikas M, Setkus A, Stange M, Ulbikas J, Ulyashin A
228 - 234	Photoresponse of pulsed laser deposited ZnO:Cu thin films Saini M, Singh R, Mitra A, Som T
235 - 246	Thermal performance analysis of a flat plate solar collector by utilizing helically corrugated risers: An experimental study Sakhaei SA, Valipour MS
247 - 269	A materials perspective on radiative cooling structures for buildings Li WX, Li YR, Shah KW
270 - 288	2-Terminal CIGS-perovskite tandem cells: A layer by layer exploration Jacobsson TJ, Hultqvist A, Svanstrom S, Riekehr L, Cappel UB, Unger E, Rensmo H, Johansson EMJ, Edoff M, Boschloo G
289 - 304	Efficient design of an artificially roughened solar air heater with semi-cylindrical side walls: CFD and exergy analysis Nidhul K, Yadav AK, Anish S, Arunachala UC
305 - 316	A robust global MPPT to mitigate partial shading of triple-junction solar cell-based system using manta ray foraging optimization algorithm Fathy A, Rezk H, Yousri D
317 - 335	BIPV/T facades - A new opportunity for integrated collector-storage solar water heaters? Part 1: State-of-the-art, theory and potential Pugsley A, Zacharopoulos A, Mondol JD, Smyth M
336 - 346	Parameters estimation of solar photovoltaic models via a self-adaptive ensemble-based differential evolution Liang J, Qiao KJ, Yu KJ, Ge SL, Qu BY, Xu RH, Li K
347 - 366	Metal oxides and noble metals application in organic solar cells Maake PJ, Bolokang AS, Arendse CJ, Vohra V, Iwuoha EI, Motaung DE
367 - 378	Solar calcination at pilot scale in a continuous flow multistage horizontal fluidized bed Esence T, Guillot E, Tessonneaud M, Sans JL, Flamant G
379 - 387	Indoor/outdoor light-harvesting by coupling low-cost organic solar cell with a luminescent solar concentrator Mateen F, Saeed MA, Shim JW, Hong SK
388 - 397	Selective light transmission as a leading innovation for solar swimming pool covers Wache R, Fielder T, Dickinson WEC, Hall JL, Adlington P, Sweeney SJ, Clowes SK
398 - 408	Investigation of the effective operational parameters of self-cleaning glass surface coating to improve methylene blue removal efficiency; application in solar cells Hosseini MS, Ebratkhahan M, Shayegan Z, Niaei A, Salari D, Rostami A, Raeisipour J
409 - 418	High efficiency metallic nanoshells for improving polymer solar cells performance: An opto-electrical study Omrani M, Fallah H, Hajimahmoodzadeh M
419 - 427	CZTS solar cell with non-toxic buffer layer: A study on the sulphurization temperature and absorber layer thickness Prabeesh P, Sajeesh VG, Selvam IP, Bharati MSD, Rao GM, Potty SN
428 - 435	Effect of triphenylethylene analogues on the performance of carbazole-based dye-sensitized solar cells Yan YQ, Zhu YZ, Dai PP, Han J, Yan M, Zheng JY
436 - 440	Enhanced open-circuit voltage in p-type passivated emitter and rear cell by doped polysilicon layer as passivation contact Xu YJ, Shen HL, Yang Z, Wei QZ, Ni ZC, Li SB, Wang ZH, Zhao BX
441 - 449	Novel BiVO4 nanostructures for environmental remediation, enhanced photoelectrocatalytic water oxidation and electrochemical energy storage performance Reddy CV, Reddy IN, Koutavarapu R, Reddy KR, Kim D, Shim J
450 - 457	A non-intrusive optical (NIO) approach to characterize heliostats in utility-scale power tower plants: Sensitivity study Mitchell RA, Zhu GD
458 - 470	Application of phase change materials, thermal insulation, and external shading for thermal comfort improvement and cooling energy demand reduction in an office building under different coastal tropical climates Nematchoua MK, Noelson JCV, Saadi I, Kenfack H, Andrianaharinjaka AZFR, Ngoumdoum DF, Sela JB, Reiter S
471 - 478	Universal strategy for all-weather and all-terrain radiative cooling with non-reciprocal mid-infrared windows Wei MM, Wu WC, Li D, Xu H, Lu YH, Song WJ
479 - 485	Efficiency enhancement of CIGS solar cell by WS2 as window layer through numerical modelling tool Sobayel K, Shahinuzzaman M, Amin N, Karim MR, Dar MA, Gul R, Alghoul MA, Sopian K, Hasan AKM, Akhtaruzzaman M
486 - 495	Solar cell using spray casted Cs2SnI6 perovskite thin films on chemical bath deposited CdS yielding high open circuit voltage Suazo FJA, Shaji S, Avellaneda DA, Aguilar-Martinez JA, Krishnan B
496 - 502	Properties of thermally evaporated CZTS thin films and numerical simulation of earth abundant and non toxic CZTS/Zn(S,O) based solar cells Khemiri N, Chamekh S, Kanzari M
503 - 516	Performance analysis of a flat plate collector to achieve a fixed outlet temperature under semi-arid climatic conditions Sarwar J, Khan MR, Rehan M, Asim M, Kazim AH
517 - 527	Synergetic or colliding effects on the solar-electric conversion efficiency from light-trapping structured surfaces: Coupling optical-electrical features of bifacial solar cells Xu YP, Zhang J, Xuan YM, Wang JL, Meng FY
528 - 538	Surface properties tuning of exfoliated graphitic carbon nitride for multiple photocatalytic performance Baca M, Rychtowski P, Wrobel R, Mijowska E, Kalenczuk RJ, Zielinska B
539 - 563	Improving solar cooker performance using phase change materials: A comprehensive review Omara AAM, Abuelnuor AAA, Mohammed HA, Habibi D, Younis O
564 - 578	Impact of field design and location on the techno-economic performance of fixed-tilt and single-axis tracked bifacial photovoltaic power plants Chudinzow D, Klenk M, Eltrop L
579 - 591	Numerical analysis guidelines for the design of efficient novel nip structures for perovskite solar cell Khattak YH, Baig F, Shuja A, Beg S, Soucase BM
592 - 598	Light harvesting enhancement by hierarchical Au/TiO2 microspheres consisted with nanorod units for dye sensitized solar cells He X, Guo Y, Li X, Liu JH
599 - 608	NH2-UiO-66 with heterogeneous pores assists zinc indium sulfide in accelerating the photocatalytic H-2 evolution under visible-light irradiation Zhao CX, Jiang HL, Liang Q, Zhou M, Zhang YZ, Li ZY, Xu S
609 - 617	Surface damage and metal-catalyzed chemical etching investigation of multicrystalline silicon by diamond wire sawing Wu XW, Tan Y, Li JY, Cai M, Li PT
618 - 625	The preparation of all-inorganic CsPbI2-xB1+x perovskite solar cells based on electrodeposited PbO2 film Lv P, Zhang PT, Chen Z, Dong SK, Liu MY, Ma JP, Cai JH, Sun FH, Li SJ
626 - 639	Short-term energy use prediction of solar-assisted water heating system: Application case of combined attention-based LSTM and time-series decomposition Heidari A, Khovalyg D
640 - 650	Effect of cutting parameters on surface integrity of monocrystalline silicon sawn with an endless diamond wire saw Costa EC, Xavier FA, Knoblauch R, Binder C, Weingaertner WL
651 - 658	CZTSSe solar cell with an efficiency of 10.19% based on absorbers with homogeneous composition and structure using a novel two-step annealing process Ren GA, Zhuang DM, Zhao M, Wei YW, Wu YX, Li XC, Lyu XY, Wang C, Li YX
659 - 667	In-situ preparation of ZnO/Cu2-xS on AZO conductive substrate and applied as counter electrode for quantum dot sensitized solar cells Chen YF, Li YY, Wu CX, Wang DJ, Lin YH, Zhang XT, Zou XX, Xie TF
668 - 682	Study on the wind-induced fatigue of heliostat based on the joint distribution of wind speed and direction Luo H, Li Z, Xiong Q, Jiang AM
683 - 692	Meta-heuristic optimization algorithms based direct current and DC link voltage controllers for three-phase grid connected photovoltaic inverter Aouchiche N
693 - 702	Enhancing the open circuit voltage of the SnS based heterojunction solar cell using NiO HTL Ahmmed S, Aktar A, Hossain J, Ismail AM
703 - 719	Investigation on performance of an asphalt solar collector: CFD analysis, experimental validation and neural network modeling Masoumi AP, Tajalli-Ardekani E, Golneshan AA
720 - 728	A 2,5-difluoro benzene-based low cost and efficient polymer donor for non-fullerene solar cells Kini GP, Park HS, Jeon SJ, Han YW, Moon DK
729 - 735	Hotspot development and shading response of shingled PV modules Clement CE, Singh JP, Birgersson E, Wang Y, Khoo YS
736 - 742	Effective Mn dopant on optical and electrical properties of CdxMn1-xSe films for quantum dot sensitized solar cell application Tung H, Phuc DH, Thang BV, Jun HK
743 - 758	Compound parabolic concentrator solar air collection-storage system based on micro-heat pipe arrays Wang ZY, Diao YH, Zhao YH, Wei XQ, Chen CQ, Wang TY, Liang L
759 - 766	First-principles screening and design of C275-based organic dyes for highly efficient dye-sensitized solar cells Shao YY, Wei Z, Mendoza LMM, Lu T, Chen SG, Li MJ, Lu WC
767 - 776	Understanding the efficacy of electron and hole transport layers in realizing efficient chromium doped BiFeO3 ferroelectric photovoltaic devices Renuka H, Joshna P, Venkataraman BH, Ramaswamy K, Kundu S
796 - 812	The influence of atmospheric boundary layer turbulence on the design wind loads and cost of heliostats Emes MJ, Jafari A, Coventry J, Arjomandi M
813 - 824	Performance analysis of triple-pass solar air heater system: Effects of adding a net of tubes below absorber surface Yassien HNS, Alomar OR, Salih MMM
825 - 831	Fluorine-doped indium oxide (IFO) layers produced by ultrasonic spray pyrolysis as electron-selective contacts in IFO/SiOx/p-Si heterojunction crystalline silicon solar cells with an open-circuit voltage of 640 mV Untila GG, Kost TN, Chebotareva AB
832 - 840	Bismuth molybdate heterojunction composited by nickel hydroxide ultrafine nanosheet with high photodecomposition efficiency Mao Y, Qiu B, Zhang M, Yin HF, Yao JC, Liu XH, Chen SM
841 - 850	Evaluation and prediction of dye-sensitized solar cells stability under different accelerated ageing conditions Chalkias DA, Loizos DD, Papanicolaou GC
851 - 873	A review on current injection techniques for low-voltage ride-through and grid fault conditions in grid-connected photovoltaic system Hassan Z, Amir A, Selvaraj J, Rahim NA
874 - 892	Dye-sensitized solar cells (DSSCs) as a potential photovoltaic technology for the self-powered internet of things (IoTs) applications Aslam A, Mehmood U, Arshad MH, Ishfaq A, Zaheer J, Khan AU, Sufyan M
893 - 902	Device simulations: Toward the design of > 13% efficient PbS colloidal quantum dot solar cell Pandey R, Khanna A, Singh K, Patel SK, Singh H, Madan J
903 - 916	Cost-effective solar cookers: A global review Arunachala UC, Kundapur A
917 - 924	Design and simulation of perovskite solar cells based on graphene and TiO2/graphene nanocomposite as electron transport layer Dadashbeik M, Fathi D, Eskandari M
925 - 936	Worldwide evaluation and correction of irradiance measurements from personal weather stations under all-sky conditions Lorente JL, Liu XQ, Morrow DJ
937 - 956	A review on sensible heat based packed bed solar thermal energy storage system for low temperature applications Gautam A, Saini RP
957 - 973	Exergy analysis of solar central receivers Laporte-Azcue M, Gonzalez-Gomez PA, Rodriguez-Sanchez MR, Santana D
974 - 1001	Nanofluids as solar spectrum splitters: A critical review Sajid MU, Bicer Y
1002 - 1008	Innovative and industrially viable approach to fabricate AlOx rear passivated ultra-thin Cu(In, Ga)Se-2 (CIGS) solar cells Birant G, de Wild J, Kohl T, Buldu DG, Brammertz G, Meuris M, Poortmans J, Vermang B
1009 - 1020	Evaporative cooling in building roofs: Local parametric and global analyses (Part-2) da Veiga AP, Guths S, da Silva AK
1021 - 1036	An empirical validation of daylighting tools: Assessing radiance parameters and simulation settings in Ladybug and Honeybee against field measurements Kharvari F
1037 - 1044	Enhanced catalytic properties of bimetallic sulfides with the assistance of graphene oxide for accelerating triiodide reduction in dye-sensitized solar cells Yu HY, Qian C, Ren HJ, Chen M, Tang DM, Wu HY, Lv RG
1045 - 1054	Photovoltaic system monitoring for high latitude locations Ogaard MB, Riise HN, Haug H, Sartori S, Selj JH
1055 - 1069	Experimental and numerical investigation on thermal performance of a quartz tube solid particle solar receiver Nie FL, Yu YP, Bai FW, Wang ZF
1070 - 1077	A per-unit-single-diode-model parameter extraction algorithm: A high-quality solution without reduced-dimensions search Panchal AK
1078 - 1087	Multiphysics-coupled study of wind load effects on optical performance of parabolic trough collector Zhang Z, Sun J, Wang L, Wei JJ
1088 - 1121	Electron transport properties analysis of titanium dioxide dye-sensitized solar cells (TiO2-DSSCs) based natural dyes using electrochemical impedance spectroscopy concept: A review Omar A, Ali MS, Abd Rahim N
1122 - 1131	Evaporative cooling in building roofs: Theoretical modeling and experimental validation (Part-1) da Veiga AP, Guths S, da Silva AK
1132 - 1145	Electrodeposited black cobalt selective coatings for application in solar thermal collectors: Fabrication, characterization, and stability Herrera-Zamora DM, Lizama-Tzec FI, Santos-Gonzalez I, Rodriguez-Carvajal RA, Garcia-Valladares O, Ares-Muzio O, Oskam G
1146 - 1157	Review of GIGS-based solar cells manufacturing by structural engineering Mufti N, Amrillah T, Taufiq A, Sunaryono, Aripriharta, Diantoro M, Zulhadjri, Nur H
1158 - 1164	Highly effective SnS composite counter electrode sandwiched bi-function CeO2:Er3+/Yb3+ assisted surface modified photoelectroded dye sensitized solar cell exceeds 9.5% efficiency Ambapuram M, Maddala G, Simhachalam NB, Sripada S, Kalvapalli S, Pedda VSY, Mitty R
1165 - 1171	Inverted planar perovskite solar cells with efficient and stability via optimized cathode-interfacial layer Zhao ZQ, Huang J, Cao Y, Sun ZZ, Cheng N, Sun SJ, Sun HB, You S
1172 - 1190	Thermo-hydraulic optimization of a solar air heater duct with non-periodic rows of rectangular winglet pairs Dezan DJ, Rocha AD, Salviano LO, Ferreira WG
1191 - 1201	Optimal rule-based control for the management of thermal energy storage in a Canadian solar district heating system Saloux E, Candanedo JA
1202 - 1213	Water-dispersible polyaniline/graphene oxide counter electrodes for dye-sensitized solar cells: Influence of synthesis route on the device performance Lemos HG, Barba D, Selopal GS, Wang C, Wang ZMM, Duong A, Rosei F, Santos SF, Venancio EC
1214 - 1221	Solar vapor generation using bubbly flow nanofluids with collaborative light-harvesting nanoparticles Yao GS, Feng YJ, Liu GH, Xu JL
1222 - 1230	Spherical-chain silica with super-hydrophobic surface and ultra-low refractive index for multi-functional broadband antireflective coatings Zhang SM, Xiao PW, Wang PM, Luo JH, Jiang B
1231 - 1239	Impact of CdS layer thickness on the composition, structure and photovoltaic performance of superstrate CZTSSe solar cells Pakstas V, Grinciene G, Kamarauskas E, Giraitis R, Skapas M, Selskis A, Juskenas R, Niaura G, Franckevicius M
1240 - 1246	Novel mixed solution of ethanol/MACl for improving the crystallinity of air-processed triple cation perovskite solar cells Ahmed DS, Mohammed MKA
1247 - 1258	Evaluation of aging and performance of grid-connected photovoltaic system northern Oman: Seven years' experimental study Kazem HA, Chaichan MT, Al-Waeli AHA, Sopian K
1259 - 1268	Design of a solar photovoltaic system for a Ro-Ro ship and estimation of performance analysis: A case study Karatug C, Durmusoglu Y
1269 - 1281	Thermal performance enhancement of tube-type alternative indirect solar dryer with iron mesh modification Sozen A, Sirin C, Khanlari A, Tuncer AD, Gurbuz EY
1282 - 1299	Preparation of phosphorus-modified BiOx as versatile catalyst for enhanced photo-reduction of Cr(VI) and oxidation of organic dyes Khazaee Z, Mahjoub AR, Khavar AHC, Srivastava V, Sillanpaa M
1300 - 1307	Efficient carrier utilization induced by conductive polypyrrole additives in organic-inorganic halide perovskite solar cells Zarenezhad H, Balkan T, Solati N, Halali M, Askari M, Kaya S
1308 - 1320	Improving performance of solar roof tiles by incorporating phase change material Alim MA, Tao Z, Abden MJ, Rahman A, Samali B
1321 - 1347	Review on photovoltaic/thermal hybrid solar collectors: Classifications, applications and new systems Herez A, El Hage H, Lemenand T, Ramadan M, Khaled M
1348 - 1355	First principle study on hybrid organic-inorganic perovskite ASnBr(3) (A = Formamidinium, Dimethylammonium and Azetidinium) Raja DB, Sundaram KS, Vidya R
1356 - 1363	The effect of dodecylammonium chloride on the film morphology, crystallinity, and performance of lead-free Bi-based solution-processed photovoltaics devices Ali N, Attique S, Rauf S, Wang XY, Khesro A, Ali S, Asghar MI, Yang SK, Lund PD, Wu HZ
1364 - 1383	Reduction of mislead power and mismatch power loss under partial shading conditions using novel square matrix shade dispersion technique Manjunath, Suresh HN, Rajanna S
1384 - 1389	Sun tracking by heliostats with arbitrary orientation of primary and secondary axes Grigoriev V, Milidonis K, Blanco M
1390 - 1403	Bayesian updating of solar resource data for risk mitigation in project finance Jadidi H, Firouzi A, Rastegar MA, Zandi M
1404 - 1426	Analytical study of evacuated annulus tube collector assisted solar desaltification system: A review Singh AK, Samsher
1427 - 1433	Polymer solar cell based on ternary active layer consists of medium bandgap polymer and two non-fullerene acceptors Sharma GD, Bucher L, Desbois N, Gros CP, Gupta G, Malhotra P
1434 - 1444	Improving the daylighting performance of residential light wells by reflecting and redirecting approaches Bugeat A, Beckers B, Fernandez E