Chemical Engineering Research & Design

Chemical Engineering Research & Design, Vol.125 Entire volume, number list

ISSN: 0263-8762 (Print)

In this Issue (45 articles)

1 - 8	Performance evaluation of process tomography system for cold flow catalytic column Acharya R, Yenumula L, Kumar U, Patankar VH, Kar S, Dash A
9 - 23	Synchronized Bayesian state estimation in batch processes using a two-dimensional particle filter Zhou S, Wang YZ, Liu YL, Ji GL
24 - 34	Estimation of gas induction in jet loop reactors: Influence of nozzle designs Sharma DV, Patwardhan AW, Ranade VV
35 - 45	Preparation, characterization and anti-fouling properties of nanoclays embedded polypropylene mixed matrix membranes Taghaddosi S, Akbari A, Yegani R
46 - 56	CFD modeling of styrene polymerization in a CSTR Xu CZ, Wang JJ, Gu XP, Feng LF
57 - 71	Process development for chemical stabilization of fly ash from municipal solid waste incineration Vavva C, Voutsas E, Magoulas K
72 - 78	Techno-economic impacts of varied compositional profiles of sugarcane experimental hybrids on a biorefinery producing sugar, ethanol and electricity Mendes FM, Dias MOS, Ferraz A, Milagres AMF, Santos JC, Bonomi A
79 - 87	A new empirical model to correlate solute solubility in supercritical carbon dioxide in presence of co-solvent Soltani S, Mazloumi SH
88 - 95	Mass and heat transfer from the surface of a gas sparged pool of liquid to an immiscible liquid under swirl flow and potential applications Sedahmed GH, Abdel-Aziz MH, Abdo MSE, Hassan MS, Konsowa AH
96 - 107	Feasibility study of LSCF5582 membrane integration into a nitrogen based chemical looping air separation process Paymooni K, Doroodchi E, Motuzas J, da Costa JCD, Moghtaderi B
108 - 118	The design analysis of continuous bioreactors in series with recirculation using Singular Value Decomposition Gomez-Perez CA, Espinosa J
119 - 129	Prediction of product morphology of lyophilized drugs in the case of Vacuum Induced Surface Freezing Pisano R, Capozzi LC
130 - 145	Process for n-butyl acrylate production using reactive distillation: Design, control and economic evaluation Moraru MD, Bildea CS
146 - 155	Temperature controlled interval contact design for ultrasound assisted liquid-liquid extraction John JJ, Kuhn S, Braeken L, Van Geruen T
156 - 165	Effect of mixed matrix membranes comprising a novel trinuclear zinc MOF, fumed silica nanoparticles and PES on CO2/CH4 separation Mandavi H, Moradi-Garakani F
166 - 180	Simultaneous design of separation sequences and whole process energy integration Leeson D, Fennell P, Mac Dowell N, Shah N
181 - 189	Equilibrium and kinetics of uranium(VI) extraction from a sulfate leach liquor solution by Alamine 336 using single drop technique Khanramaki F, Shirani AS, Safdari J, Torkaman R
190 - 203	Hydrodynamic performance of the ASI impeller in an aerated bioreactor containing the biopolymer solution through tomography and CFD Khalili F, Nasr MRJ, Kazemzadeh A, Ein-Mozaffari F
204 - 213	Integrating a vapor recompression heat pump into a lower partitioned reactive dividing-wall column for better energy-saving performance Feng SY, Ye Q, Xia H, Li R, Suo XM
214 - 225	Fabrication of a magnetic porous hydrogel sphere for efficient enrichment of Rb+ and Cs+ from aqueous solution Zhu YF, Zhang HF, Wang WB, Ye XS, Wu ZJ, Wang AQ
226 - 232	Experimental characterization of stable liquid rivulets on inclined surfaces: Influence of surface tension, viscosity and inclination angle on the interfacial area Bonart H, Marek A, Repke JU
233 - 244	Residence time distribution in a biomass pretreatment reactor: Experimentation and modeling Youssef Z, Ducept F, Bennaceur H, Malinowska B, Almeida G, Perre P, Flick D
245 - 256	Energy efficient configuration of Membrane Distillation units for brackish water desalination using exergy analysis Ali E
257 - 264	Phase holdup distribution and dispersion performance in a novel liquid-liquid cyclone reactor of isobutane alkylation catalyzed by ionic liquid Zhang MY, Wang L, Zhu LY, Wang ZB, Liu ZC, Jin YH
265 - 281	Methodical design and operation of membrane distillation plants for desalination Hagedorn A, Fieg G, Winter D, Koschikowski J, Mann T
282 - 290	Flow field in a liquid-liquid cyclone reactor for isobutane alkylation catalyzed by ionic liquid Zhang MY, Zhu LY, Wang ZB, Liu ZC, Liu ZZ, Xu CM, Jin YH
291 - 305	Superporous pellicular kappa-Carrageenan-Nickel composite beads; morphological, physical and hydrodynamics evaluation for expanded bed adsorption application Abatari MN, Emami MRS, Jahanshahi M, Shahavi MH
306 - 318	Effects of sand and flocculation on dewaterability of kaolin slurries aimed at treating mature oil sands tailings Angle CW, Gharib S
319 - 327	Comparison of the adsorption preference using superparamagnetic Fe3O4-SH nanoparticles to remove aqueous heavy metal contaminants Lin S, Liu L, Yang Y, Zhang W, Lian C, Lin KF
328 - 347	Principles of viscous sintering in amorphous powders: A critical review Kamyabi M, Sotudeh-Gharebagh R, Zarghami R, Saleh K
348 - 360	Hybrid process for the purification of water contaminated with nitrites: Ion exchange plus catalytic reduction Mendow G, Grosso CI, Sanchez A, Querini CA
361 - 366	Modeling of purge-gas recovery using membrane separation Zhang DM, Wang HZ, Li CX, Meng H
367 - 384	Formulation optimization of reverse microemulsions using design of experiments for nanoparticles synthesis Nourafkan E, Gao H, Hu ZL, Wen DS
385 - 397	Preliminary techno-economic analysis of non-commercial ceramic and organosilica membranes for hydrogen peroxide ultrapurification Abejon R, Abejon A, Puthai W, Ibrahim SB, Nagasawa H, Tsuru T, Garea A
398 - 407	Predicting hydrodynamic parameters and volumetric gas-liquid mass transfer coefficient in an external-loop airlift reactor by support vector regression Kojic P, Oniorjan R
408 - 421	ZnO nanoparticles loaded different mesh size of porous activated carbon prepared from Pinus eldarica and its effects on simultaneous removal of dyes: Multivariate optimization Jafari M, Rahimi MR, Ghaedi M, Dashtian K
422 - 432	Optimal design for dividing wall column using support vector machine and particle swarm optimization Jia SK, Qian X, Yuan XG
433 - 448	Simplifying and synthesizing practical four-product dividing wall column configurations Ge XL, Liu BT, Yuan XG, Liu BT
449 - 460	Numerical study on impact behavior of nanoparticle shapes on the performance improvement of shell and tube heat exchanger Hajabdollahi H, Hajabdollahi Z
461 - 470	Numerical study on flow behavior of ultrafine powders in conical spouted bed with coarse particles Sun LY, Luo K, Fan JR
471 - 482	Effects of operational models (batch, continuous and CFID modes) on the performance of a single A(2)O airlift bioreactor for treatment of milk processing wastewater Asadi A, Zinatizadeh AA, van Loosdrecht M
483 - 493	Hydrodynamics of pulsed columns: The effect of new parameters affecting the pressure drop Charton S, Thebault M, Winn S, Roussel H, Lamadie F, Hlawitschka MW, Korb C, Bart HJ
494 - 510	CFD-PBM simulation of dense emulsion flows in a high-shear rotor-stator mixer Michael V, Prosser R, Kowalski A
511 - 522	Development of a zone flow model for the confined impeller stirred tank (CIST) based on mean velocity and turbulence measurements Komrakova AE, Liu Z, Machado MB, Kresta SM
523 - 537	Evaluation of the performance of a simulation model for open algae ponds and investigation of the operating behavior of open algae ponds over a one-year period for different locations Rarrek A, Rehfeldt S, Klein H