화학공학소재연구정보센터
홈 로그인 로그아웃 연락처 사이트맵
Journal of the Korean Industrial and Engineering Chemistry, Vol.20, No.3, 258-265, June, 2009
Export Citation
방향족/지방족 혼합 Diisocyanate를 포함하는 Polyurethane 분산체의 제조와 성질
Preparation and Properties of Polyurethane Dispersions with Aromatic/Aliphatic Mixed Diisocyanate
김형석†, 노시태
  • 한양대학교 공과대학 화학공학과
Hyoung Sug Kim†, and Si Tae Noh
  • Department of Chemical Engineering, Hanyang University, Ansan 426-791, Korea
E-mail:
초록
Poly(tetramethylene glycol) (PTMG, Mw = 2000), dicyclohexylmethane-4,4'-diisocyanate (H12-MDI)와 4,4'-diphenylmethane diisocyanate (MDI)의 이소시아네이트 혼합물, 그리고 음이온기로서 dimethylol propionic acid (DMPA)를 사용하여 프리폴리머 혼합법으로 음이온성 폴리우레탄 분산체(PUD)를 합성하였다. 프리폴리머의 중화제로서는 triethylamine (TEA)을, 그리고 프리폴리머의 가지연장제로는 ethylene diamine (EDA)를 사용하였다. DMPA의 몰비율과 혼합이소시아네이트에서 방향족 이소시아네이트의 함양이 PUD의 입자크기와 점도변화에 미치는 영향을 연구하였다. 그리고 또한 DMPA의 몰비율과 방향족 이소시아네이트 함양 변화에 따른 PUD 도막의 기계적 성질과 열적 성질에 대해서도 논의하였다. DMPA의 몰비율이 증가할수록 음이온성 PUD의 입자크기와 점도가 감소하였으나, 동일한 DMPA 함량에서는 이소시아네이트 혼합물 중 방향족 이소시아네이트의 함량이 증가 할수록 입자의 크기와 점도가 증가하는 경향을 나타냈다. 혼합 이소시아네이트의 몰비율이 일정할 때 PUD 도막의 인장강도는 DMPA의 함량이 증가함에 따라 증가하였으나, 신장율은 감소하였다. PUD 도막의 열분해 온도에 있어서, DMPA 함량에 대한 영향은 크게 나타났으나, 방향족 이소시아네이트 함양의 영향은 DMPA 함량이 낮은 조건에서는 상대적으로 크지 않았다.
An anionic polyurethane dispersions (PUDs) were synthesized from the poly (tetramethylene glycol) (PTMG, Mw = 2000g/mol), mixed isocyanate of dicyclohexylmethane-4,4'-diisocyanate (H12-MDI) and 4,4'-diphenylmethane diisocyanate (MDI), and dimethylol propionic acid (DMPA) as anionic site, following a prepolymer mixing process. Triethylamine (TEA) was used as a neutralization agent and the ethylenediamine (EDA) as the chain extender of the prepolymer. The effects of the DMPA molar ratio and aromatic diisocyanate content in the mixed isocyanate on the particle size and viscosity of PUD were studied. Also, the mechanical and thermal properties of the PUD cast films were discussed according to the molar ratio of DMPA and aromatic isocyanate content. It was found that the particle size and the viscosity of an anionic PUD decreased with increasing DMPA molar ratio but increased with increasing aromatic isocyanate (MDI) content in the mixed isocyanate at the constant DMPA content. Tensile strength of the PUD cast films increased and elongation at break decreased with increasing DMPA content at the constant mixed isocyanate molar ratios. In thermal degradation temperature of PUD cast films, the effect of DMPA contents was great but the effect of aromatic isocyanate contents at the low DMPA content was very slight respectively.
Keywords:polyurethane;anionic polyurethane dispersion;aromatic isocyanate;mixed isocyanate;thermal degradation temperature
  1. Dieterich D, In Progress in Organic Coatings, 9, 281 (1981)
  2. Bayer AG, Ger. Offen., 1,495,745 (1963)
  3. U. S. Patent, 3,479,310 (1969)
  4. Dieterich D, Reiff H, Angew. Makromol. Chem., 26, 85 (1972)
  5. Dieterich D, Reiff H, Adv. Urethane Sci. Technol., 4, 112 (1976)
  6. Hepburn C, Polyurethane Elastomers, 2’d edition, 10, Elsevier Science Publishers Ltd, New York (1991)
  7. Kim BK, Kim TK, J. Appl. Polym. Sci., 43, 393 (1991)
  8. Kim BK, Kim TK, J. Appl. Polym. Sci., 43, 2295 (1991)
  9. Kim CK, Kim BK, Jeong HM, Colloid and Polym. Sci., 269, 895 (1991)
  10. Kim TK, Kim BK, Colloid and Polym. Sci., 269, 889 (1991)
  11. U. S. Patent, 2,968,575 (1954)
  12. U. S. Patent, 3,437,624 (1969)
  13. David DJ, Staley HB, Analytical chemistry of polyurethane, Hight polymer series, XVI, Part III, Wiley Interscience, New York (1969)
  14. Han IK, Oh BK, Lee YM, Noh ST, J. Korean Ind. Eng. Chem., 3(4), 595 (1992)
  15. Dieterich D, Progr. Org. Coat., 9, 281 (1981)
  16. Rutger IR, Rheol. Acta, 2, 305 (1962)
  17. Kim KW, Polym.(Korea), 4(2), 96 (1980)
  18. Saunder FL, Rheological properties of Latex, In Advances in Emulsion Polymerization and Latex Technology, vol II, Notes Compiled by M. El-Aasser, Lehigh Univ., Bethlehem, PA. (1990)
  19. Buscall R, Corner T, Stageman JF, In Polymer Colloids, Elsevier, New York (1985)
  20. Frisch KC, Klempner D, In Advances in urethane Science and Technology, 121, Technomic Publishing Company, Weatport (1987)
  21. Huang SM, Chen TK, J. Appl. Polym. Sci., 105(6), 3794 (2007)
  22. Durrieu V, Gandini A, Belgacem MN, Blayo A, Eisele G, Putaux JL, J. Appl. Polym. Sci., 94(2), 700 (2004)
  23. Kim IH, Shin JS, Cheong IW, Kim JI, Kim JH, Colloids and Surfaces A: Physicochemical and Engineering Aspects, 207, 169 (2002)
  24. Lorenz O, August HJ, Angew. Makromol. Chem., 63, 11 (1977)
  25. Hepburn C, In Polyurethane Elastomers, Elsevier Science Publishers Ltd, New York (1982)
  26. Ahn TO, Jung SU, Jeong HM, Lee SW, J. Appl. Polym. Sci., 51(1), 43 (1994)
  27. Fabris HJ, Adv. Urethane Sci. Technol., 4, 89 (1976)
  28. Oyer E, Wright GC, J. Am. Chem. Soc., 81, 2138 (1959)
  29. Chem Y, Chem YL, J. Appl. Polym. Sci., 46, 435 (1992)