| 2973 - 2978 |
Use of polymers for cement-based structural materials
Chung DDL |
| 2979 - 2988 |
Effect of impact modification on slow crack growth in poly(vinyl chloride)
Bernal-Lara TE, Hu Y, Summers J, Hiltner A, Baer E |
| 2989 - 2995 |
Sliding performance of polymer composites in liquid hydrogen and liquid nitrogen
Zhang Z, Klein P, Theiler G, Hubner W, Ubner R |
| 2997 - 3001 |
Preparation and properties of polymer matrix piezoelectric composites containing aligned BaTiO3 whiskers
Chen LF, Hong YP, Chen XJ, Wu QL, Huang QJ, Luo XT |
| 3003 - 3013 |
Nano-sized beads and porous fiber constructs of poly(epsilon-caprolactone) produced by electrospinning
Hsu CM, Shivkumar S |
| 3015 - 3024 |
Dehydration and rehydration processes of cement paste exposed to high temperature environments
Alonso C, Fernandez L |
| 3025 - 3029 |
A study of mechanochemical reduction of lead sulphide by elemental iron on the surface by X-ray photoelectron spectroscopy
Godocikova E, Bastl Z, Spirovova I, Balaz P |
| 3031 - 3039 |
Dislocation structure in low-angle interfaces between bonded Si(001) wafers
Akatsu T, Scholz R, Gosele U |
| 3041 - 3046 |
Diffusion bonding of Pd-Ag rolled membranes
Tosti S, Bettinali L |
| 3047 - 3055 |
The thermo-mechanical behaviour of Cu-Cr in-situ composite
Lee KL |
| 3057 - 3061 |
Effect of grain size on elastic modulus and hardness of nanocrystalline ZrO2-3 wt% Y2O3 ceramic
Chaim R, Hefetz M |
| 3063 - 3067 |
Effects of changes in temperature on fatigue crack growth of adhesively bonded Al 2080/SiC/20p-2080 Al laminated composites
Hassan HA, Lewandowski JJ, Abd El-Latif MH |
| 3069 - 3077 |
A process for the preparation of polyaniline salt doped with acid and surfactant groups using benzoyl peroxide
Ram MS, Palaniappan S |
| 3079 - 3083 |
Preparation, sintering, and microstructures of strontium barium bismuth tantalate layered perovskite ceramics
Lu CH, Bai JH, Chen H |
| 3085 - 3088 |
Aspects of the reproducibility of mechanical properties in Al based foams
Kennedy AR |
| 3089 - 3094 |
Measurement of yield strength of thin metal film
Wang F, Xu KW |
| 3095 - 3103 |
Study of the preparation of ruthenia based catalytic materials by heating their precursors
Balek V, Labhsetwar NK, Mitsuhashi T, Haneda H, Subrt J, Zelenak V |
| 3105 - 3114 |
Piezoelectric paint: Ceramic-polymer composites for vibration sensors
White JR, De Poumeyrol B, Hale JM, Stephenson R |
| 3115 - 3119 |
Damage and plastic flow in a Al-Si-Cu thixocast alloy
Cerri E |
| 3121 - 3128 |
Fique fiber-reinforced polyester composites: Effects of fiber surface treatments on mechanical behavior
Ganan P, Mondragon I |
| 3129 - 3135 |
Ferroelectric phase transition in sol-gel derived Bi-doped PLZT ceramics
Dutta S, Choudhary RNP, Sinha PK |
| 3137 - 3140 |
Machinable and mechanical properties of sintered Al2O3-Ti3SiC2 composites
Luo YM, Li SQ, Pan W, Chen J, Wang RG |
| 3141 - 3145 |
Optical, mechanical properties and infiltration rate of spinel/zirconia-glass dental composites prepared by melt infiltration
Lee DY |
| 3149 - 3150 |
Preparation and characterization of copper-activated carbon composite electrodes for supercapacitors
Meng QH, Liu L, Ling LC |
| 3151 - 3153 |
Preparation and characterization of poly(vinyl butyral)/Na+-montmorillonite nanocomposite
Cho CH, Cho MS, Sung JH, Choi HJ, Jhon MS |
| 3155 - 3157 |
Study of polymer humidity sensor array on silicon wafer
Wang J, Shi KH, Chen LH, Zhang XJ |
| 3159 - 3161 |
Brazing Si3N4 ceramic using a Cu-Pd-Ti filler alloy for high-temperature applications
Zhang J, Naka M, Zhou Y |
| 3163 - 3165 |
Conduction mechanisms in Cu-GeO2 thin cermet films
Lucy IB |
| 3167 - 3169 |
Synthesis and characterization of nanocrystalline aluminum nitride from a low temperature combustion precursor
Kuang JC, Zhang CR, Zhou XG, Wang SQ |
| 3171 - 3173 |
Phase stability and electrical properties of (Bi0.925La0.075)(2)Ti2O7 thin films by chemical solution deposition
Yang XN, Wang H, Shang S, Yao WF, Zhang Y, Liu YH, Zhou JT |
| 3175 - 3177 |
Empirical method for the determination of hardness from low-load ball indentation tests for brittle materials
Gong JH, Bao YW |
| 3179 - 3181 |
Characterization of rate-dependent loading/unloading dynamic constitutive behavior of aluminum alloy by Lagrange experiment
Yan M, Dai LH, Shen LT, Shan JL |
| 3183 - 3186 |
Preliminary investigation into the load bearing capacity of ion beam surface modified UHMWPE
Shi W, Li XY, Dong H |
| 3187 - 3189 |
Influence of gas phase composition on the defects formation in lithium niobate
Tsirlin M |
| 3191 - 3193 |
Tensile behavior of SiCp/Al composites subjected to quasi-static and high strain-rate loading
Wang Y, Zhou YX, Xia YM |
| 3195 - 3197 |
Effects of annealing temperature on the carrier concentrations, the carrier mobilities and the quality of nitrogen doped ZnO films deposited by magnetron sputtering
Lim JM, Shin KC, Lee CM |
| 3199 - 3200 |
Transmission electron microscopy investigation of the interface formation between silicon and anodic alumina
Muller F, Muller AD, Schulze S, Hietschold M |
| 3201 - 3202 |
XPS determination of the binding energies of phosphorus and nitrogen in phosphazenes
Vassileva P, Krastev V, Lakov L, Peshev O |
| 3203 - 3205 |
Formation of C54TiSi(2) thin films by using high-temperature sputtering and rapid thermal annealing
Lee SJ, Kim DY, Kim TW |
| 3207 - 3210 |
Synthesis and processing of lanthanum strontium manganite (La0.84Sr0.16MnO3) powder by co-precipitation technique
Ramanathan S, Singh PK, Kakade MB, De PK |
| 3211 - 3212 |
Ultrasonic-assisted fabrication of metal matrix nanocomposites
Li XC, Yang Y, Cheng XD |
| 3213 - 3215 |
Mooney-type relation for the porosity dependence of the effective tensile modulus of ceramics
Pabst W, Gregorova E |
| 3217 - 3219 |
Effect of annealing on neutron-transmutation-doped GaN epilayers grown on sapphire substrates
Park SH, Kang TW, Kim TW |
| 3221 - 3225 |
Nano-scaled hydroxyapatite/polymer composite - II. Coating of sintered hydroxyapatite particles on poly(2-(o-[1'-methylpropylideneamino] carboxyamino) ethyl methacrylate)-grafted silk fibroin fibers through covalent linkage
Korematsu A, Furuzono T, Yasuda S, Tanaka J, Kishida A |
| 3227 - 3233 |
Carbon nanocoils with changed coiling-chirality formed over Ni/molecular Sieves catalyst
Chen XQ, Yang SM, Motojima S |
| 3235 - 3236 |
Room temperature growth of high quality ZnO thin film on sapphire substrates
Kim NH, Kim HW |
| 3237 - 3239 |
Micro-patterns of Ruthenium(II) complexes produced by micromolding
Wang Z, Zou G, Liu JP, He PS |
| 3241 - 3243 |
Electroless plating of carbon nanotubes with silver
Feng Y, Yuan HL |
| 3245 - 3247 |
Wood pulp fiber reinforced melamine-formaldehyde composites
Gindl W, Jeronimidis G |
| 3249 - 3251 |
SEM morphology and XRD characterization of Ni microstructure arrays synthesized by dc electrodeposition in porous polycarbonate templates
Kumar S, Kumar S, Chakarvarti SK |
| 3253 - 3255 |
Effect of interleaf sequence on impact damage and residual strength in a graphite/epoxy laminate
Yi XS, An XF |
| 3257 - 3259 |
Electrochemical synthesis of copper nanotubules in etched ion tracks in polycarbonate
Kumar S, Kumar S, Chakarvarti SK |
| 3261 - 3264 |
Organic modification on TiO2 nanoparticles by grafting polymer
Zan L, Liu ZS, Zhong JC, Peng ZG |
| 3265 - 3266 |
Formation of the rutile TiO2 under ultrasonic irradiation
Guo WL, Wang XK |
