Polymer Engineering and Science

Polymer Engineering and Science, Vol.48, No.4 Entire volume, number list

ISSN: 0032-3888 (Print)

In this Issue (25 articles)

627 - 633	Effects of thermal aging on isotactic polypropylene crystallinity Law A, Simon L, Lee-Sullivan P
634 - 641	Effect of annealing and orientation on microstructures and mechanical properties of polylactic acid Yu L, Liu HS, Xie FW, Chen L, Li XX
642 - 648	Oxygen permeability of biaxially oriented polypropylene films Lin YJ, Dias P, Chen HY, Chum S, Hiltner A, Baer E
649 - 655	Solid-state blending of poly(ethylene terephthalate) with polystyrene: Extent of compatibilization and its dependence on blend composition Schexnaydre RJ, Mitchell BS
656 - 661	Rheological characterization of room temperature vulcanized silicone sealant: Effect of filler particle size Xu XM, Gao CH, Zheng Q
662 - 675	Condensed-phase flame retardation in nylon 6-layered silicate nanocomposites: Films, fibers, and fabrics Shanmuganathan K, Deodhar S, Dembsey NA, Fan QG, Patra PK
676 - 682	Compression hysteresis of fibrous systems Stankovic SB
683 - 686	Foam formation from fluorinated polyphosphazenes by liquid CO2 processing Steely LB, Li QX, Badding JV, Allcock HR
687 - 696	Improved through-plane electrical conductivity in a carbon-filled thermoplastic via foaming Motlagh GH, Hrymak AN, Thompson MR
697 - 704	Effect of molecular weight and molding conditions on the replication of injection moldings with micro-scale v-groove features Murakami O, Kotaki M, Hamada H
705 - 710	Fibril formation of 1,3 : 2,4-di(3,4-dimethylbenzylidene) sorbitol in polymer melts Lipp J, Shuster M, Terry AE, Cohen Y
711 - 716	Advanced injection molding mold and molding process for improvement of weld line strengths and isotropy of glass fiber filled aromatic polyester LCP Koponen M, Enqvist J, Nguyen-Chung T, Mennig G
717 - 722	Local thermo-oxidative degradation in injection molding Schmiederer D, Gardocki A, Kuhnert I, Schmachtenberg E
723 - 731	Characterization of new formulations for the rotational molding based on ethylene-propylene copolymer/graphite nanocomposites Planes E, Duchet J, Maazouz A, Gerard JF
732 - 746	Effects of welding procedures on mechanical and morphological properties of hot gas butt welded PE, PP, and PVC sheets Balkan O, Demirer H, Ezdesir A, Yildirim H
747 - 755	Yield stress and rheological characterization of the low shear zone of an epoxy molding compound for encapsulation of semiconductor devices Yoshii M
756 - 766	A comparative study of dispersing a polyamide 6 into a polypropylene melt in a Buss Kneader, continuous mixer, and modular intermeshing corotating and counter-rotating twin screw extruders Shon K, Bumm SH, White JL
767 - 773	Simulation of the residual stresses in the contour laser welding of thermoplastics Potente H, Wilke L, Ridder H, Mahnken R, Shaban A
774 - 785	Calculation and significance of the maximum polymer surface temperature T* in reciprocating cylinder-on-plate sliding Samyn P, Schoukens G
786 - 794	Determination of different morphological structures in PC/ABS open spiral injection moldings O-Charoen N, Leong YW, Hamada H
795 - 805	Synthetic 6FDA-ODA copolyimide membranes for gas separation and pervaporation: Correlation of separation properties with diamine monomers Xiao SD, Feng XS, Huang RYM
806 - 814	In-line measurements of the morphological parameters of PP/PA6 blends during extrusion in the transient mode Pinheiro LA, Hu GH, Pessan LA, Canevaro SV
815 - 822	The mastication characteristics of powdered carbon black filled natural rubber during internal mixing Zhang AQ, Lin YL, Wang LS
823 - 828	Synthesis and characterization of hollow polyaniline microtubes and microbelts with nanostructured walls in sodium dodecyl sulfate micellar solutions Wu TM, Lin YW
829 - 836	Thermal degradation and physical aging of poly(lactic acid) and its blends with starch Acioli-Moura R, Sun XS