| 1529 - 1543 |
Anionic Copolymerization of Nylon 6/12: A Comprehensive Review
Mohammadi M, Ahmadi S, Ghasemi I, Rahnama M |
| 1544 - 1551 |
Influence of vacuum on the porosity and mechanical properties in rotational molding
Vetter L, Werner J, Wolf M, Hertle S, Drummer D |
| 1552 - 1559 |
Influence of screw configuration and processing temperature on the properties of short glass fiber reinforced polypropylene composites
Lekube BM, Purgleitner B, Renner K, Burgstaller C |
| 1560 - 1569 |
Properties of microinjection-molded polypropylene/graphite composites
Zhou ST, Hrymak AN, Kamal MR, Jiang RZ |
| 1570 - 1584 |
Effect of interfacial chemistry on crystallization of polypropylene/multiwall carbon nanotube nanocomposites
Wang PH, Gulgunje P, Ghoshal S, Odeh IN, Verghese N, Kumar S |
| 1585 - 1592 |
Viscoelastic behavior and constitutive modeling of PP/HNT composites prepared by water-assisted extrusion
Huang YX, Huang HX |
| 1593 - 1602 |
Thermoplastic polyurethane/polytetrafluoroethylene/bridged dopo derivative composites: Flammability, thermal stability, and mechanical properties
Zhou Y, He WD, Wang N, Xu DH, Chen XL, He M, Guo JB |
| 1603 - 1610 |
Synthesis and self-healing behavior of thermoreversible epoxy resins modified with nitrile butadiene rubber
Feng LB, Zhao HW, He X, Zhao YH, Gou LXH, Wang YP |
| 1611 - 1623 |
Synthesizing radiation-hard polymer and copolymers using laccol monomers extracted from lacquer tree toxicodendron succedanea via cationic polymerization
Arachchilage IHAM, Patel MK, Harmon JP |
| 1624 - 1635 |
Interface porosity in multilayered all-conducting polymer electrodes
Borras N, Estrany F, Aleman C |
| 1636 - 1647 |
Mechanical characterization of graphene oxide reinforced epoxy at different strain rates
Majzoobi GH, Nejad SHA, Sabet SAR |
| 1648 - 1656 |
Estimates for material shrinkage in molded parts caused by time-varying cavity pressures
Bushko WC, Stokes VK |
| 1657 - 1666 |
Tough and recoverable triple-network hydrogels based on multiple pairs of toughing mechanisms with excellent ionic conductivity as stable strain sensors
Li S, Bu XM, Wu LL, Ma XF, Diao WJ, Zhuang ZZ, Zhou YM |
| 1667 - 1677 |
Relationships between crystalline structure and the thermal behavior of poly(ethylene 2,5-furandicarboxylate): An in situ simultaneous SAXS-WAXS study
Stoclet G, Arias A, Yeniad B, De Vos S |
| 1678 - 1687 |
On the modeling and optimization of UV-curable fluoro-siloxane formulations and their solvent absorption and adhesion properties
Crook RA, Allen A |
| 1688 - 1694 |
Processability study of in-mold coating for sheet molding compound compression molded parts
Ko S, Ouyang XL, Straus EJ, Lee LJ, Castro JM |
| 1695 - 1700 |
Investigation of the strain-rate-dependent mechanical behavior of a photopolymer matrix composite with fumed nano-silica filler
Asif M, Ramezani M, Khan KA, Khan MA, Aw KC |
| 1701 - 1709 |
Influence of thermal annealing on mechanical properties and in vitro degradation of poly(p-dioxanone)
Zhang JF, Jones S, Wang DH, Wood A, Washington T, Acreman K, Cuevas B, Karau A |
| 1710 - 1718 |
The influence of the type of polypropylene and the length of the flow path on the structure and properties of injection molded parts with the weld lines
Bociaga E, Kaptacz S, Duda P, Rudawska A |
| 1719 - 1728 |
Preparation and characterization of hydrophilic temperature-dependent polyurethane containing the grafted poly(N-isopropylacrylamide)
Chung YC, Bae JC, Choi JW, Chun BC |
| 1729 - 1738 |
Controlling properties of acrylate/epoxy interpenetrating polymer networks by premature termination of radical polymerization of acrylate
Li WL, Delpouve N, Araujo S, Batteux F, Bobo E, Saiter JM, Tan L, Negahban M |
