Polymer Engineering and Science

Polymer Engineering and Science, Vol.48, No.9 Entire volume, number list

ISSN: 0032-3888 (Print)

In this Issue (25 articles)

1655 - 1660	Morphology and glass transition of thin polylactic acid films Narladkar A, Balnois E, Vignaud G, Grohens Y, Bardeau JF
1661 - 1666	Electrospinning and alignment of polyaniline-based nanowires and nanotubes Attout A, Yunus S, Bertrand P
1667 - 1673	Properties of new nanocomposite triblock copolymer gels based on expandable graphite Paglicawan MA, Kim JK
1674 - 1677	Natural rubber nanocomposite reinforced with nano silica Chen Y, Peng Z, Kong LX, Huang MF, Li PW
1678 - 1682	Review: Increasing the efficiency of the extrusion process Sikora JW
1683 - 1692	Miscibility, melting, and crystallization behavior of poly(hydroxybutyrate) and poly(D,L-lactic acid) blends Gunaratne LMWK, Shanks RA
1693 - 1706	Characterization of viscoelastic fluid flow in a periodically driven cavity: Flow structure, frequency response, and phase lag Sriram S, Deshpande AP, Pushpavanam S
1707 - 1717	Numerical prediction of phase-change heat conduction of injection-molded high density polyethylene thick-walled parts via the enthalpy transforming model with mushy zone Yang B, Fu XR, Yang W, Huang L, Yang MB, Feng JM
1718 - 1724	Microstructure and water vapor transport properties of functionalized carbon nanotube-reinforced dense-segmented polyurethane composite membranes Mondal S, Hu JL
1725 - 1736	Multiscale roughness analysis in injection-molding process Bigerelle M, Van Gorp A, Iost A
1737 - 1746	A simplified approach to predict part temperature and minimum "safe" cycle time Hioe Y, Chang KC, Zuyev K, Bhagavatula N, Castro JM
1747 - 1754	In situ compatibilization of maleated thermoplastic starch/polyester melt-blends by reactive extrusion Raquez JM, Nabar Y, Narayan R, Dubois P
1755 - 1767	Chromophore concentration effect on holographic grating formation efficiency in novel azobenzene-functionalized polymers Schab-Balcerzak E, Sobolewska A, Miniewicz A, Jurusik J
1768 - 1777	Radiation and postirradiation crosslinking and structure of two unsaturated polyester resins Pucic I, Jurkin T
1778 - 1784	Formation and characterization of polyurethane-vermiculite clay nanocomposite foams Patro TU, Harikrishnan G, Misra A, Khakhar DV
1785 - 1792	Effect of molecular weight and end capping on poly(lactic-co-glycolic acid) ultrasound contrast agents Eisenbrey JR, Burstein OM, Wheatley MA
1793 - 1800	In situ reactive compatibilization of aramid/polystyrene blends using amine-functionalized polystyrene Shabbir S, Zulfiqar S, Ahmad Z, Sarwar MI
1801 - 1814	Three-dimensional simulation of primary and secondary penetration in a clip-shaped square tube during a gas-assisted injection molding process Chau SW
1815 - 1823	Pressure and temperature behavior of thermoplastic polymer melts during high-pressure expansion injection molding Rogelj S, Krajnc M
1824 - 1832	Mechanical and tribological properties of polyoxymethylene modified with nanoparticles and solid lubricants Sun LH, Yang ZG, Li XH
1833 - 1839	Water bamboo husk reinforced poly(lactic acid) green composites Wang KH, Wu TM, Shih YF, Huang CM
1840 - 1847	Prediction of residual stress and viscoelastic deformation of film insert molded parts Kim SY, Oh HJ, Kim SH, Kim CH, Lee SH, Youn JR
1848 - 1854	The morphology, mechanical properties, and flammability of aligned electrospun polycarbonate (PC) nanofibers Moon SC, Farris RJ
1855 - 1861	Uniaxial tensile properties underlying plane-stress rapid fracture resistance in polyethylene Oezbek P, Leevers P
1862 - 1870	Rheological characterization of starch derivatives/polycaprolactone blends processed by reactive extrusion Bossard F, Pillin I, Aubry T, Grohens Y