| 871 - 888 |
Experimental investigation and numerical simulation of injection molding with micro-features
Yu LY, Koh CG, Lee LJ, Koelling KW, Madou MJ |
| 889 - 898 |
Development of orientation and mechanical properties of extrusion cast polyamide 11 films in biaxial stretching process
Rhee S, White JL |
| 899 - 910 |
Numerical investigation of continuous processes for catalytic hydrogenation of nitrile butadiene rubber
Pan QM, Rempel GL, Ng FTT |
| 911 - 924 |
Modification of porous suspension-PVC particles by stabilizer-free aqueous dispersion polymerization of absorbed monomers
Shach-Caplan M, Narkis M, Silverstein MS |
| 925 - 939 |
Flow patterns and mixing mechanisms in the screw mixing element of a co-rotating twin-screw extruder
Ishikawa T, Amano T, Kihara SI, Funatsu K |
| 940 - 950 |
Effect of melt temperature and skin-core morphology on the mechanical performance of nylon 6
Murthy NS, Kagan VA, Bray RG |
| 951 - 960 |
Effect of a compatibilizer on the structural development of a thermotropic liquid crystalline polymer/polystyrene blend
Seo Y, Kim HJ, Kim YJ, Rhee HW |
| 961 - 968 |
Miscibility evolution of polycarbonate/polystyrene blends during compounding
Chuai CZ, Almdal K, Johannsen I, Lyngaae-Jorgensen J |
| 969 - 982 |
High speed imaging of drop formation from low viscosity liquids and polymer melts in spinning disk atomization
Senuma Y, Hilborn JG |
| 983 - 993 |
Tensile modulus of polymer nanocomposites
Ji XL, Jing JK, Jiang W, Jiang BZ |
| 994 - 1018 |
Self-reinforced polypropylene/LCP extruded strands and their moldings
Liang YC, Isayev AI |
| 1019 - 1031 |
Studies of spinodal decomposition in a ternary polymer-solvent-nonsolvent system
Saxena R, Caneba GT |
| 1032 - 1045 |
Mechanical performance of starch based bioactive composite biomaterials molded with preferred orientation
Sousa RA, Mano JF, Reis RL, Cunha AM, Bevis MJ |
| 1046 - 1055 |
Strain-rate and temperature effects on the deformation of polypropylene and its simulation under monotonic compression and bending
Ohashi F, Hiroe T, Fujiwara K, Matsuo H |
| 1056 - 1069 |
Monitoring the reaction progress of a high-performance phenylethynyl-terminated poly(etherimide). Part I: Cure kinetics modeling
Bullions TA, McGrath JE, Loos AC |
| 1070 - 1081 |
Improved properties of SBS-modified asphalt with dynamic vulcanization
Wen G, Zhang Y, Zhang YX, Sun K, Fan YZ |
| 1082 - 1097 |
Haze of polyethylene films - Effects of material parameters and clarifying agents
Andreassen E, Larsen A, Nord-Varhaug K, Skar M, Oysaed H |
| 1098 - 1114 |
Residual thermal stresses in injection moldings of thermoplastics: A theoretical and experimental study
Kamal MR, Lai-Fook RA, Hernandez-Aguilar JR |
| 1115 - 1129 |
Improved modeling for the reheat phase in thermoforming through an uncertainty treatment of the key parameters
Yousefi A, Bendada A, Diraddo R |
